Tech Netgear Router Not Connecting to Device? Let’s Fix It!

Netgear Router Not Connecting to Device? Let’s Fix It!

-

- Advertisment -

As soon as you are done performing Netgear router setup via Netgear Nighthawk router login page, you can access its network on any device and begin enjoying its seamless network. However, in case, you are unable to access the network on any device, then there is an issue. So, take a walk through the hacks given in this post to find the troubleshooting hacks that will help you out to fix the issue.

Netgear Router Can’t Connect to Device [Resolved]

  1. Ensure the Correctness of the Setup Process

The very first reason that comes to mind for not being able to access the Netgear router network after setup is the incorrect method followed to set up the router. So, refer to the user manual right away and check the steps given there to verify if the same steps were followed. Followed the right steps? Try the next hack.

  1. Alter the Connection Source

Netgear Router not connecting

Another reason why you are unable to access the Netgear router network is because you made the mistake of connecting the Netgear router and the modem using a wireless medium. There is nothing wrong with connecting the devices via a wireless medium but FYI, it is less reliable than a wired connection. Your connection can drop at any time if you are using a wireless connection between the router and modem. Therefore, it is recommended that you alter the connection source between the devices. So, take the help of an Ethernet cable and establish a wired connection between the Netgear router and modem now. After following this hack, see if the Netgear router network can be accessed on devices. On the off chance, it is still troubling you, then follow the next troubleshooting hack.

  1. Relocate the Netgear Router

Perhaps the Netgear router is placed very far from the modem in your house. If the connection between the devices is weak, how do you expect that you will be able to access the router’s network? So, we recommend you relocate your Netgear router without wasting any time. So unplug it from its existing socket and plug it into the one located near the modem. While you are doing so, keep in mind that you are not placing them very close either. Else, the signals that your networking devices are emitting will clash.

  1. Remove WiFi Interference

Make sure that your Netgear router is not kept near any transmitting appliances, electronic devices, metal objects, or reflexive surfaces. Smart TVs, Cordless phones, Bluetooth speakers, mirrors, fish tanks, treadmills, baby monitors, microwave ovens, and refrigerators are examples of any such things that should be away from your router.

  1. Bring Device Closer

If you are trying to access the Netgear router WiFi from a distant place then you won’t be able to access it’s network properly. The device should be in the router’s range to avoid any issues. So, bring the accessing device closer to the Netgear router and then try if the issue is fixed.

  1. Update Firmware

An obsolete firmware on the Netgear router can also result in such issues. So, it is recommended that you keep the Netgear router firmware to the most recent version. If it is not updated, then access the Netgear Genie dashboard using http://routerlogin.net and update the firmware right away. This will also enhance the overall performance of the router.

  1. Reset Netgear Router

If by following the hacks mentioned above, you haven’t been able to access the Netgear router’s network, then the possibility of incorrectly setting up the router increases. That means either you have followed incorrect steps or missed out on any step during the setup process. So, now you need to reset the Netgear router and delete every single personalized setting done by you. Press the Reset button located on the router to do this job. Done? The default factory settings have been restored on the Netgear router now. It is now time to set it up again. You can set it up by any of the below-given methods:

Netgear Router

Check Also: 5 Handy Tips for Extending a Wireless Network

  1. Manual method or Web-based interface method

  2. WPS method

  3. Nighthawk App method

Use the exact steps mentioned in the user manual to get the setup process done.

The Conclusion

Not being able to access the Netgear router network after performing its setup is not a new issue. By taking the help of the troubleshooting hacks mentioned in this guide, you will be able to get rid of the obstacle that is stopping you from accessing the router network on any device.

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Latest news

In-Depth Guide to Perform Wavlink WiFi Extender Setup

The need for fast internet is rapidly growing day by day! Everybody wants to have access to high-speed internet...

Unable to Join SSID of Wavlink Extender? Let’s Help You!

Accessing a fast internet connection everywhere in the house is a dream of every user across the globe. That...

Easy and Simple Way to Perform Comfast Firmware Update

In this technological era, the Comfast WiFi extender has a huge reputation in the networking device industry as it...

Four Best Techniques to Troubleshoot Arlo Camera Login Issues

Experiencing the Arlo camera login issues have been faced by plenty of users out there these days. In case,...
- Advertisement -

Comfast Extender Won’t Pick Up 5GHz Signals [Troubleshooting]

Having a dual-band WiFi range extender installed in the house seems useless when it fails to pick up the...

Tips To Improve Slow Internet Speed of Wavlink Extender

In this technological world, millions of people perform the Wavlink WiFi extender setup to get high-speed internet coverage throughout...

Must read

In-Depth Guide to Perform Wavlink WiFi Extender Setup

The need for fast internet is rapidly growing day...

Unable to Join SSID of Wavlink Extender? Let’s Help You!

Accessing a fast internet connection everywhere in the house...
- Advertisement -

You might also likeRELATED
Recommended to you